The KWA Grade 2 syllabus latest update is crucial for candidates preparing for Draftsman Grade II under Kerala Water Authority. A clear idea of the syllabus helps you focus on the right topics and avoid wasting time.
Since the exam covers core civil engineering fundamentals, you should follow a structured plan from the start.
Since the exam covers core civil engineering fundamentals, a structured plan will give you an advantage.
KWA Grade 2 Syllabus Latest – Key Highlights
Before going into the KWA Grade 2 syllabus latest, check these details:
• Post: Draftsman Grade II (KWA)
• Category Nos. 548/2025
• Total Marks: 100
• Exam Mode: OMR
• Subject Level: Diploma Civil Engineering
Each section carries specific weight. Therefore, smart preparation becomes important.
Basic Engineering Drawing (10 Marks)
• Drawing instruments, equipment and materials
• Lettering, dimensioning and scale
• Plane geometrical construction
• Conic section and projection
Units and Mensuration (6 Marks)
• Units of measurements
• Measurement of perimeter and area of triangles, polygons and circles
• Volume of solids
AutoCAD (8 Marks)
• Introduction to AutoCAD
• Basic commands
• Drawing toolbar and modifying toolbar
• Plotting and printing
Surveying (9 Marks)
This part of the KWA Grade 2 syllabus latest covers surveying basics.
• Conventional surveying
• Terms used in chain, compass, plane table and levelling survey
• Principle of levelling
• Types of levelling
• Reduction of levels
• Contouring
• Theodolite survey
• Modern and advanced surveying instruments
Building Materials and Construction (10 Marks)
• Stone, brick, tiles, cement, lime and filler materials
• Plain cement concrete and reinforced cement concrete
• Timber
• Foundation
• Masonry
• Roofing
• Flooring
• Building finishes and services
• Temporary structural treatment for building construction
Building Drawing and Estimating (10 Marks)
• Building rules and bye-laws
• Estimation
• Rules and methods of measurement of work
• Rate analysis
• Valuation
Hydraulics and Irrigation (9 Marks)
• Terms used in irrigation
• Storage and diversion head works
• Reservoir, dam, canals
• Cross drainage works
• Properties of fluid
• Measurement of pressure
• Types of hydraulic energy
Mechanical & Drafting Topics
Module 1: Development & Interpenetration (5 Marks)
• Definition and need of development
• Methods of developing surfaces
• Development of surfaces bounded by plane of revolution
• Development of oblique cone with elliptical base
• Calculation of developed lengths of geometrical solids
• Intersection and interpenetration curves
• Methods to find interpenetration curves
• Problems on interpenetration of prism, cones and pyramids
• Intersection of cylinder
Module 2: Fasteners, Welds & Locking Devices (10 Marks)
Fasteners
• Screw threads – terms and nomenclature
• Types of screw threads and uses
• Threads as per SP46:2003
• Bolts, nuts, studs – proportions and uses
Welds
• Welded joints and representation
• Welding symbols as per SP-46
Locking Devices
• Types of locking devices
• Machine screws, cap screws, set screws
• Foundation bolts and uses
Pipe Joints
• Types of pipe joints
Module 3: Pipe Joints & Riveted Joints (3 Marks)
• Expansion joints, loops and pipe fittings
• Types of rivets, proportions and uses
• Types of riveted joints and terms
• Conventional representation
• Rivet size vs plate thickness relationship
• Arrangement of rivets
• Failure of riveted joints
• Efficiency of riveted joints
Module 4: Belt Drive & Gear Drive (7 Marks)
Belt Drive
• Materials of belts
• Slip and creep
• Velocity and arc of contact
• Calculations – belt speed, number of belts, pulley ratio
• Standard pulleys and chain drive
Gear Drive
• Types of gears
• Cast and machined gears
• Gear profiles
Module 5: Hydraulics & Pneumatics (5 Marks)
Hydraulics
• Hydraulic system components
• Hydraulic jack – working principle
• Hydraulic actuators
• DC valve, non-return valve, throttle valve
Pneumatics
• Pneumatic system basics
• FRL unit
• Pneumatic actuators
Module 6: Limits, Fits & Tolerance (4 Marks)
• Limits, fits and tolerance
• Toleranced dimensioning
• Geometrical tolerance
• Machining and surface finish symbols
• Interchangeable parts
• IS: 919 and IS: 2709
Module 7: Bearings (4 Marks)
• Types of bearings
• Advantages of bearings
• Friction reduction
🎥 Complete Roadmap for KWA Grade 2 Preparation
A clear roadmap will help you cover the KWA Grade 2 syllabus latest effectively.
👉 Watch full video (syllabus + study plan + course details):
https://youtu.be/OCWLAofwLh0?si=NzMIBkPpUzmxb1pt
This video explains everything step by step.
📄 View Full KWA Grade 2 Syllabus PDF
Additionally, always refer to the official syllabus while preparing. It ensures accuracy and complete coverage.
📞 Need Guidance? Contact Now
For more details about preparation and courses:
👉 90378 17002
👉 82899 55605
Get expert support and clear your doubts quickly.
💡 Final Thoughts
The KWA Grade 2 syllabus latest covers all essential civil engineering basics. With the right strategy, you can complete it without stress.
Stay consistent, revise smartly, and aim for steady progress. 🚀
